GETTING FAMILIAR WITH PLUMBING: A MUST FOR INSTALLING A BATHTUB

Getting Familiar with Plumbing: A Must for Installing a Bathtub

Getting Familiar with Plumbing: A Must for Installing a Bathtub

Blog Article

Schedule Here

What are your ideas about Installing A Bathtub?


How to Install a Bathtub
Setting up a tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bath tub with a new one is additionally a moderately challenging project. If the old tub is readily easily accessible, the job can move rapidly; if you need to open a wall to remove the old tub as well as position the brand-new bath tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will need an assistant to move out the old bathtub as well as set in the new one. Make certain you have certified yourself for the job and are comfortable attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is far better to take into consideration employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your washroom if you have already purchased a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your devices as well as product checklist should consist of the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Planning for the Setup


    To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to prevent pressure on the bath tub.
    Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the provided washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its final setting.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, turn on the faucets to drain any water staying in the system. The process of removing the existing faucets can be fairly bothersome as a result of the restricted access that is usually the instance.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipes. Once the supply pipelines have actually been removed, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
    Before going on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

    Mounting the Bath tub


    Making use of the two wood boards under its feet, position the tub in the needed position. The wooden boards are useful in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
    The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bathtub until the spirit level reviews degree.
    To mount faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
    Switch on the water and examine all joints and also new pipework for leaks and tighten them if necessary. Fill up the bath tub as well as likewise inspect the overflow electrical outlet and the normal electrical outlet for leakages.
    Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the bathtub should wait up until the tub has actually been made use of a minimum of once as this will certainly resolve it right into its last placement.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipes.
    If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next off, position the faucet in the placing opening in the bath/basin making certain that the washers are in area in between the tap and the sink. Secure the faucet in place with the producer provided backnut. Once the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous kind must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, creating the water to pass through the wall surface between the bathroom and the tiling, causing issues with wetness as well as feasible leakages to the ceiling listed below.
    You can select from a variety of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealant can break rather early if you do not take into account this movement before securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is recommended to fit the floor tiles using waterproof or waterproof glue as well as cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub Yourself

    We hope you liked our part about A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for taking time to browse our article post. Sharing is caring. One never knows, you could be helping someone out. We recognize the value of reading our article about How to Install a Bathtub Yourself.


    Hire A Pro

    Report this page